Jump to content

Photo

Rear Hub & Axle Maintenance

- - - - - Rear Bearings half-shaft

  • Please log in to reply
13 replies to this topic

#1
ChrisA

ChrisA

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 659 posts
  • Location:Richmond, VA
  • Region:NCR
  • Car Year:1999
  • Car Number:58

So how is maintenance handled for the rear hubs and half-shafts? I got a set of rear uprights and had new bearings and seals pressed in and I'm debating on whether I should install them now or just wait until something back there starts to go? The ones on there now have 83K on them and have never been touched. My concern is if a bearing or half-shaft fails at the track and I have difficulty separating the two. I'm not sure I have room in the truck to carry spares of both the uprights and axles. I only have an open trailer, so limited in amount I can bring along. What are others doing/what's recommended? If you had to chose which spares, rear hubs or axles, to bring with you, which would you choose?


Chris

 

Happiness is a dry martini and a good woman ... or a bad woman.
- George Burns


#2
Jeff Wasilko

Jeff Wasilko

    Member

  • Members
  • PipPipPip
  • 271 posts
  • Location:Boston, MA
  • Region:NER
  • Car Year:1995
  • Car Number:08

the rear hubs and bearings are wear items and should get replaced regularly. I do them every 2 years. Sadly I've been in 2 cars where the rear hub failed causing the wheel to depart. One mine, one an enduro team's car.

 

I had asked my shop to replace both rear hubs and bearings, but for some reason they put one old hub back on after changing the bearing.



#3
38bfast

38bfast

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 1,113 posts
  • Location:Sterling Heights, MI
  • Region:OVR
  • Car Year:1999
  • Car Number:38
We will put on used street car hub flanges or new from mazda. Raced hub flanges get replaced once a year or whenever a wheel gets hit. Many have not replaced them after a hit and then pay the price a few races later.
  • Jim Drago likes this
Ralph Provitz
V2 Motorsports

#4
davew

davew

    Veteran Member

  • SMembers
  • PipPipPipPipPip
  • 2,297 posts
  • Location:Beloit, Wi
  • Region:Chicago
  • Car Year:1999
  • Car Number:72

There is no periodic maintenance on the rear bearings/hubs. Unlike the front hubs which can be repacked, these are not servicable.

 

replace the bearings when they get loose. Inspect the hubs for wear or cracks whenever you replace the bearing.

 

After any contact, a good inspection is required. Ralph likes to change the hub after contact. Let your concience be your guide.


Dave Wheeler
Advanced Autosports, the nations most complete Spec Miata shop
Author, Spec Miata Constructors Guide, version 1 and 2.0

Building Championship winning cars since 1995

4 time Central Division Spec Miata Champion car builder 2012-2013-2014-2017

Back to Back June Sprints Spec Miata 1-2 finishes 2016 and 2017

5 time June Sprints winner in Mazda's

6 Time Northern Conference Champion Car Builder

2014 SCCA Majors National point Champion car builder

2014 SCCA Runoffs winner, T4 (Bender)

2014 Central Division Champion, ITS (Wheeler)

2013 Thunderhill 25 hour winning crew chief

2007 June Sprints winner, (GT1, Mohrhauser)

Over 200 race wins and counting.
www.advanced-autosports.com
dave@advanced-autosports.com
608-313-1230

Survive the 25, NASA Thunderhill - Survive the 25, NASA Thunderhill We have a Winnah! - Won their 1st race... Congratulations! Sponsor / Advertiser - Site sponsor / advertiser... support these guys! Donor - Made PayPal donation Bona fide - A bonafide Spec Miata driver

#5
ChrisA

ChrisA

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 659 posts
  • Location:Richmond, VA
  • Region:NCR
  • Car Year:1999
  • Car Number:58
How about the axles? Are folks cleaning and regreasing periodically or just carrying new spares? Higher confidence with certain brands? Any difficulties getting the shaft out of the hubs?

Chris

 

Happiness is a dry martini and a good woman ... or a bad woman.
- George Burns


#6
Ron Alan

Ron Alan

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 3,732 posts
  • Location:Northern CA
  • Car Year:1995

How about the axles? Are folks cleaning and regreasing periodically or just carrying new spares? Higher confidence with certain brands? Any difficulties getting the shaft out of the hubs?

At this point...any oem axle that is still in its original hub will more than likely come out very hard or very very very hard :) Very unlikely something you can do at the track!

 

If the axle/hub have ever been apart...especially by a racer, It will most likely have grease or anti-seize  and fall right out! 

 

I cant speak for the benefit of axle service(re grease or coated)as I have done neither. The axle failures I have seen have never been the cv joint on its own...always been another problem that led to a failure or caused the cv joint to get ruined.


Ron

RAmotorsports

 

Donor - Made PayPal donation Bona fide - A bonafide Spec Miata driver

#7
Brandon

Brandon

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 765 posts
  • Location:North Jersey
  • Region:NNJR
  • Car Year:1996
  • Car Number:48SM

Not to pile-on (but I will), I do a bearing replacement every year and as others have noted, check for other issues after contact (mainly play in the bearing itself).

 

Regarding the flanges (where the studs are pressed into), inspect them thoroughly when they're removed from the upright/bearing and smooth/polish any high areas.

Said inspection also must include using a magnifying glass on the stud holes themselves to look for cracks.

 

I keep a spare pair of uprights with me in my track box if there ever is contact during a weekend. Automatically take it out of service when that happens and replace the bearing/check the flange.

 

Axles, I get mine rebuilt by Gator Axles in Florida. Had two pair done so I've also got a spare pair (again) and it was under $400 for both sets.

Granted, my $60 in 2-day shipping via FedEx wasn't cheap but they did a fantastic turnaround in terms of time and getting them back to me.

 

HTH!

Brandon


Bona fide - A bonafide Spec Miata driver

#8
luvin_the_rings

luvin_the_rings

    Member

  • Members
  • PipPipPip
  • 204 posts
  • Location:Los Angeles, CA
  • Car Year:1990

Just separate them now and replace.  if you damage a new one, use the spare old one to replace at the track.  Once you separate it once, they fall out the rest of the time.  

 

Don't forget new axle nuts. 

 

-Z



#9
ChrisA

ChrisA

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 659 posts
  • Location:Richmond, VA
  • Region:NCR
  • Car Year:1999
  • Car Number:58

Thanks guys, sounds like my concern about separating the two for the first time at track is a valid one. I'll pick up a new set of axles to go with the uprights and rebuild the originals. So, what is better for the splnes, anti-sieze or grease?


Chris

 

Happiness is a dry martini and a good woman ... or a bad woman.
- George Burns


#10
ChrisA

ChrisA

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 659 posts
  • Location:Richmond, VA
  • Region:NCR
  • Car Year:1999
  • Car Number:58

Axles, I get mine rebuilt by Gator Axles in Florida. Had two pair done so I've also got a spare pair (again) and it was under $400 for both sets.

Granted, my $60 in 2-day shipping via FedEx wasn't cheap but they did a fantastic turnaround in terms of time and getting them back to me.

 

HTH!

Brandon

 

A little unclear, was it $400 to rebuild 2 half-shafts or 4? Also, with new units from NAPA costing $90, what's the incentive to rebuild? Are the OEs significantly better?


Chris

 

Happiness is a dry martini and a good woman ... or a bad woman.
- George Burns


#11
Brandon

Brandon

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 765 posts
  • Location:North Jersey
  • Region:NNJR
  • Car Year:1996
  • Car Number:48SM

"new" being relative with respect to the axles as I don't think they're available anymore from Mazda. Same for the uprights. Be sure to only get NB uprights for your car as yours are 5mm (I think) wider than an NA.

Flanges & bearings are identical between NA & NB.

 

For the splines I just use Permatex silver-infused anti-seize. Easy peasy and as others have noted, after you do it a couple of times the axle no longer stays rusty where it contacts the flange.


Bona fide - A bonafide Spec Miata driver

#12
Brandon

Brandon

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 765 posts
  • Location:North Jersey
  • Region:NNJR
  • Car Year:1996
  • Car Number:48SM

2 pairs (4x axles) - they disassemble, inspect, grease, install using new boots & straps. They told me they have a stash of parts they can use to replace any questionable bits found during the separation/cleaning so it's not like you're getting a non-compliant part back. That was my one concern: ending up with an axle that can be protested as non-compliant.

 

I can't comment on any NAPA or otherwise as I've never purchased any axle new, only used ones. And even then, rebuilding the one pair I did is something I'll never do again with the Gator service being that cheap.

 

A little unclear, was it $400 to rebuild 2 half-shafts or 4? Also, with new units from NAPA costing $90, what's the incentive to rebuild? Are the OEs significantly better?

 


Bona fide - A bonafide Spec Miata driver

#13
callumhay

callumhay

    Member

  • Members
  • PipPipPip
  • 163 posts
  • Location:tampa
  • Region:fl
  • Car Year:1999
  • Car Number:35
Thanks for the tip on Gator axles. I have a pair that needs rebuilding and will likely send to them. Outer CV joint on one is stiff to move and not smooth compared to other axle. Car was making noise in the right hand turns at Sebring. Swapped the spares in and was weighing options of buying new spares or rebuild

Cal

#14
ChrisA

ChrisA

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 659 posts
  • Location:Richmond, VA
  • Region:NCR
  • Car Year:1999
  • Car Number:58

2 pairs (4x axles) - they disassemble, inspect, grease, install using new boots & straps. They told me they have a stash of parts they can use to replace any questionable bits found during the separation/cleaning so it's not like you're getting a non-compliant part back. That was my one concern: ending up with an axle that can be protested as non-compliant.

 

I can't comment on any NAPA or otherwise as I've never purchased any axle new, only used ones. And even then, rebuilding the one pair I did is something I'll never do again with the Gator service being that cheap.

 

Thanks Brandon, I may look into using Gator during the off-season.


Chris

 

Happiness is a dry martini and a good woman ... or a bad woman.
- George Burns





0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users