Jump to content

Photo

Needing String Alignment System

- - - - - alignment iron canyon

  • Please log in to reply
28 replies to this topic

#21
Duncan

Duncan

    Member

  • Members
  • PipPipPip
  • 251 posts

I can't speak for Dave, but I do my alignments at home on scales using hub stands and the iron canyon string setup.  

 

I keep toe plates and a camber gauge in the trailer, as well as bringing my Iron Canyon string setup.  I use the toe plates and the camber gauge if I get bumped or have an off-track incident just to make sure that I haven't bent anything.  

If I actually have to change the alignment at the track, I generally use the strings since it's easy to setup and I can roll the car back and forth without a helper.

Duncan


Series Champ - Won a points based series in a Spec Miata Bona fide - A bonafide Spec Miata driver We have a Winnah! - Won their 1st race... Congratulations!

#22
FTodaro

FTodaro

    Veteran Member

  • SMembers
  • PipPipPipPipPip
  • 3,084 posts
  • Location:Columbus Ohio
  • Region:Great Lakes
  • Car Year:2001
  • Car Number:35

No matter what system you use, you need to use the same system all the time. When using strings, and measuring toe as the measurement between the wheel and the string, you have a 15" wheel you are measuring from. If you then measure with typical toe plates, you have a 24" measurement angle. Your 1/8" toe measurement with the strings will read as almost 1/4" with toe plates, yet nothing changed on the car, you changed your measurement system.

 

I make my own camber gauge. It is available on my website, no batteries and very easy to use.

 

Dave

There are two ways to fix this or take it into account.

1) if you run zero toe its not an issue and

2) just measure both ways in your shop before you go to the track so you know what the variance is.


Frank
TnT Racing
SCCA Ohio Valley Region
 

Make it Rain - Made Paypal donation of $100+ We have a Winnah! - Won their 1st race... Congratulations! Bona fide - A bonafide Spec Miata driver Donor - Made PayPal donation

#23
davew

davew

    Veteran Member

  • SMembers
  • PipPipPipPipPip
  • 2,297 posts
  • Location:Beloit, Wi
  • Region:Chicago
  • Car Year:1999
  • Car Number:72

Any idea how this would differ from say a commercial alignment system?  I go to a setup shop and say, lets go 1/16" out, they use a laser alignment rack and get that effective toe.  What will it read on a string box? and on toe plates? 

 

Before I started this crazy business I was a front end/suspension tech for 15 years. I have litterally done thousands of allignments on street cars. My knowledge base is 15 years ago, so I have not used the most modern computerized machines. But back in my day (said with a cremudgeon voice), the machines all based toe measurements on a 24 inch diameter tire. Thus toe plates should read the same (assuming a 24" long plate which is normal) as the machine. But strings measured to a wheel will read less by about 60%.

 

We use a hybrid string system to get thrust/steering wheel square. Then use toe plates for final adjustment. This way an at track adjustment is done the same way the shop adjustment was made.

 

No matter how you do it, do it the same way everytime.

 

Dave


Dave Wheeler
Advanced Autosports, the nations most complete Spec Miata shop
Author, Spec Miata Constructors Guide, version 1 and 2.0

Building Championship winning cars since 1995

4 time Central Division Spec Miata Champion car builder 2012-2013-2014-2017

Back to Back June Sprints Spec Miata 1-2 finishes 2016 and 2017

5 time June Sprints winner in Mazda's

6 Time Northern Conference Champion Car Builder

2014 SCCA Majors National point Champion car builder

2014 SCCA Runoffs winner, T4 (Bender)

2014 Central Division Champion, ITS (Wheeler)

2013 Thunderhill 25 hour winning crew chief

2007 June Sprints winner, (GT1, Mohrhauser)

Over 200 race wins and counting.
www.advanced-autosports.com
dave@advanced-autosports.com
608-313-1230

Survive the 25, NASA Thunderhill - Survive the 25, NASA Thunderhill We have a Winnah! - Won their 1st race... Congratulations! Sponsor / Advertiser - Site sponsor / advertiser... support these guys! Donor - Made PayPal donation Bona fide - A bonafide Spec Miata driver

#24
ChrisA

ChrisA

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 659 posts
  • Location:Richmond, VA
  • Region:NCR
  • Car Year:1999
  • Car Number:58
What are guys using for leveling platforms and/or risers to make adjustments without lifting the car and preloading the bushings?

Chris

 

Happiness is a dry martini and a good woman ... or a bad woman.
- George Burns


#25
Bench Racer

Bench Racer

    Different strokes for different folks : )

  • Members
  • PipPipPipPipPip
  • 5,508 posts
  • Location:Wauwatosa, WI
  • Region:Milwaukee
  • Car Year:1990
  • Car Number:14

What are guys using for leveling platforms and/or risers to make adjustments without lifting the car and preloading the bushings?

Made wooden stands a total of 30 inches long by 15 inches wide with a 15 inch long lowered section for scales to sit on. Used 2 by 10's with 4 adjustable legs each stand. It's a bit of a bitch to jack the car to this height, but I can slide my body under car if need be. Can reach to cam bolts and control arm pivot bolts. Lifting the car for this process is no different than lifting the car to change tires at the track. With 30 inches one can bounce and roll the car.

Did a quick search and found some steel stands/adjustable legs for $550.00 taller than those below.

A while ago there were some nice 30 inch long scale stands on the net for $500.00. With these and rocker height may be ok.

22823337-498-Roll-Off-Levelers-for-Racin

 

 They are available for 2.5" or 4" scales.
It's best to email me at info@trakktape.com for more info. I now have these in production, so get ready for racing season!

 

Seller Phone Number: 7603203734
Seller Phone Number2:
(760) 285-2220

 

Item Location: PALM SPRINGS, CA


Broken record - You are starting to sound like a broken record. Donor - Made PayPal donation Bona fide - A bonafide Spec Miata driver

#26
bmarshall1

bmarshall1

    Member

  • Members
  • PipPipPip
  • 298 posts
  • Location:United States
  • Region:SW Florida
  • Car Year:1999
  • Car Number:23

Thanks Everyone, lots of good ideas and discussions into the theory and practice of aligning.



#27
Ron Alan

Ron Alan

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 3,732 posts
  • Location:Northern CA
  • Car Year:1995

And some not so good methods :D


Ron

RAmotorsports

 

Donor - Made PayPal donation Bona fide - A bonafide Spec Miata driver

#28
Johnny D

Johnny D

    Veteran Member

  • Moderators
  • 6,121 posts
  • Location:Fremont, CA
  • Region:San Francisco
  • Car Year:1999
  • Car Number:88

FYI, there's a Set up Guide in the Downloads up top ^^.

J~


2011 NASA Western Endurance Racing Championship E3 Champ
We have a Winnah! - Won their 1st race... Congratulations! Beta-Tester - Assisted us with beta testing the website. Donor - Made PayPal donation Bona fide - A bonafide Spec Miata driver Novel Approach - When a paragraph simply won't do... Survive the 25, NASA Thunderhill - Survive the 25, NASA Thunderhill Instigator - Made a topic or post that inspired other Make it Rain - Made Paypal donation of $100+

#29
RazerX

RazerX

    Member

  • Members
  • PipPipPip
  • 318 posts
  • Region:N. Cal
  • Car Year:1999
  • Car Number:11

Before I started this crazy business I was a front end/suspension tech for 15 years. I have litterally done thousands of allignments on street cars. My knowledge base is 15 years ago, so I have not used the most modern computerized machines. But back in my day (said with a cremudgeon voice), the machines all based toe measurements on a 24 inch diameter tire. Thus toe plates should read the same (assuming a 24" long plate which is normal) as the machine. But strings measured to a wheel will read less by about 60%.

 

We use a hybrid string system to get thrust/steering wheel square. Then use toe plates for final adjustment. This way an at track adjustment is done the same way the shop adjustment was made.

 

No matter how you do it, do it the same way everytime.

 

Dave

 

 

thanks Dave.  This seems to match where we evolved to.  Trying to get toe using the string box was challenging and frustrating. 


 - Speed

 

 

We have a Winnah! - Won their 1st race... Congratulations! Survive the 25, NASA Thunderhill - Survive the 25, NASA Thunderhill Bona fide - A bonafide Spec Miata driver





Also tagged with one or more of these keywords: alignment, iron canyon

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users