Need Spec Miata Suspension Setup Guru’s Advice
#1
Posted 07-21-2011 12:25 PM
I’m new to Spec Miata racing . However I have been Road Racing for 19 years. I’m trying to set up the suspension on my 2000 Miata and I really need some advice from SM Gurus. My car is a brand new build including the suspension. Recently I took it out for my maiden race with this car. Turns out, it happened on a double race weekend. Therefore I had 5 races including 4- 15 lap Sprint races & a 1-hour Enduro as well as a practice/qual session on BOTH days. Same for Sat & Sun. I did 10 races in total. The first 3 races, I could not get the car to power out of any corners without serious oversteer. I kept backing off the rear swaybar until the only way to make the car behave was to disconnect it on one side. But throughout the rest of the races I did not feel the car could bite into the corners, tire wise.
I originally set up the car on a professional state of the art alignment machine as per Jim Daniels on-line recommendations. However according to my alignment guy, he could not adjust the car to the max camber settings that Jim recommends. So, here are my specs as raced. If you can give me any suggestions to improve this car – I’D BE GREATLY APPRECIATED!
Our track is tight 1.5 miles, 11 turns & bumpy. Clockwise.
2000 Miata (never in any accident) – super low mileage Torsen LSD, 27mm from bar.
205/50ZR15 Toyo R888 (stickers – see photos after 10 races below). The tires were run 5 races and then rotated (front to rear) for the other 5 races. Tire pressures were approx. 38psi hot.
FL (ride height = 5†to spot weld on rocker)
4.8 deg caster
0 toe
-1.9 deg camber
FR (ride height = 5†to spot weld on rocker)
4.8 deg caster
0 toe
-1.9 deg camber
RL (ride height = 4-3/4†to spot weld on rocker)
0 toe
-2.5 deg camber
RR (ride height = 4-3/4†to spot weld on rocker)
0 toe
-2.5 deg camber
Its obvious I need more neg camber. But 2.5 is all I can get according to my alignment guy. So if anyone can provide me with some suspension setup advice – I’D BE GREATLY APPRECIATED.
Thanks,
Bruce McNutt
#2
Posted 07-21-2011 12:39 PM
Lower the car to 4.5" both front and back and see what you get on camber. You should see at least 2.3 to 2.5 degrees up front at these heights. Running the allowed aftermarket "fatcat" bump stops will offer more adjustment on the ride height without running into the bump stops so if you don't have these on the car I highly recommend them.
I also suspect your over steer issue was caused by having the ride height lower in the rear. Get the ride heights even then corner weight the car.
#3
Posted 07-21-2011 01:15 PM
My broken-record advise: forget measuring at pinch welds. What matters is the distance from the top of the shock to the bottom of the bumpstop, measured with the car's weight on the springs.
You did not supply corner weights - you did corner weigh the car, didn't you? Hard to say what's happening otherwise.
-Denny
#4
Posted 07-21-2011 01:15 PM
Hi,
I’m new to Spec Miata racing . However I have been Road Racing for 19 years. I’m trying to set up the suspension on my 2000 Miata and I really need some advice from SM Gurus. My car is a brand new build including the suspension. Recently I took it out for my maiden race with this car. Turns out, it happened on a double race weekend. Therefore I had 5 races including 4- 15 lap Sprint races & a 1-hour Enduro as well as a practice/qual session on BOTH days. Same for Sat & Sun. I did 10 races in total. The first 3 races, I could not get the car to power out of any corners without serious oversteer. I kept backing off the rear swaybar until the only way to make the car behave was to disconnect it on one side. But throughout the rest of the races I did not feel the car could bite into the corners, tire wise.
I originally set up the car on a professional state of the art alignment machine as per Jim Daniels on-line recommendations. However according to my alignment guy, he could not adjust the car to the max camber settings that Jim recommends. So, here are my specs as raced. If you can give me any suggestions to improve this car – I’D BE GREATLY APPRECIATED!
Our track is tight 1.5 miles, 11 turns & bumpy. Clockwise.
2000 Miata (never in any accident) – super low mileage Torsen LSD, 27mm from bar.
205/50ZR15 Toyo R888 (stickers – see photos after 10 races below). The tires were run 5 races and then rotated (front to rear) for the other 5 races. Tire pressures were approx. 38psi hot.
FL (ride height = 5†to spot weld on rocker)
4.8 deg caster
0 toe
-1.9 deg camber
FR (ride height = 5†to spot weld on rocker)
4.8 deg caster
0 toe
-1.9 deg camber
RL (ride height = 4-3/4†to spot weld on rocker)
0 toe
-2.5 deg camber
RR (ride height = 4-3/4†to spot weld on rocker)
0 toe
-2.5 deg camber
Its obvious I need more neg camber. But 2.5 is all I can get according to my alignment guy. So if anyone can provide me with some suspension setup advice – I’D BE GREATLY APPRECIATED.
Thanks,
Bruce McNutt
Try running HOT pressures closer to 44. YES that right, these are RACE tires not street tires with race compounds.
Glenn Murphey, Crew Chief
Owner Crew Chief Services The Pinnacle of Excellence, Contract Crew Services for the racing community.
Soon to be back in the club racing scene for good
#5
Posted 07-21-2011 01:17 PM
Try running HOT pressures closer to 44. YES that right, these are RACE tires not street tires with race compounds.
Also for SP these are not even close to being worn down enough What tread depth did you start with?
Glenn Murphey, Crew Chief
Owner Crew Chief Services The Pinnacle of Excellence, Contract Crew Services for the racing community.
Soon to be back in the club racing scene for good
#6
Posted 07-21-2011 02:23 PM
Your car is too high. With you or someone your same weight in the car lower the car to between 4.25" and 4.5" to the factory pinch weld. You have reverse rake in your car now. I normally end up with the rear .125" higher than the front.
Like Glenn said try higher hot tire pressures.
#7
Posted 07-22-2011 09:13 AM
#8
Posted 07-22-2011 09:15 AM
Danny
Danny Steyn Racing | DSR YouTube Channel
Danny Steyn Photography | Adept Studios | Ocean Machinery | OPM Autosports | Rossini Racing Engines | G-Loc Brakes |
2 x SCCA Runoffs Champ | 1 x NASA National Champ | 6 x June Sprints Champ | 10 x ARRC Champ
1 x SCCA Super Sweep | 2 x Triple Crown | 4 x Hoosier Super Tour Points Champ | 6 x Majors Points Champ | 5 x SEDiv Driver of the Year
#9
Posted 07-22-2011 10:42 AM
What about toe? Our track is tight and twisty without long straights. What do you think about a little bit of toe?
#10
Posted 07-23-2011 06:36 PM
No more than 1/16 out F and 1/16 in at R You REALLY need to scale the car! GAWD knows what the cross and rear bite is.We have another crazy double weekend on Aug 20/21 with an insane amount of track time & 10 full races. I will try all of this throughout the weekend.
What about toe? Our track is tight and twisty without long straights. What do you think about a little bit of toe?
Glenn Murphey, Crew Chief
Owner Crew Chief Services The Pinnacle of Excellence, Contract Crew Services for the racing community.
Soon to be back in the club racing scene for good
#11
Posted 07-24-2011 09:05 AM
denny,My broken-record advise: forget measuring at pinch welds. What matters is the distance from the top of the shock to the bottom of the bumpstop, measured with the car's weight on the springs.
-Denny
in the spirit of being a broken record, can you elaborate again on the measurements from bump stop to top of the shock.
my pinch welds are so buggered up that i could use a different starting point for a baseline.
i ask because i am sure that i am not the only one with the question, and good info is nice to have redundant.
I thought i recall reading you say go 3/4", but please confirm.
thanks
1999 SM #92 SoPac division
#12
Posted 07-24-2011 05:38 PM
denny,
in the spirit of being a broken record, can you elaborate again on the measurements from bump stop to top of the shock.
my pinch welds are so buggered up that i could use a different starting point for a baseline.
i ask because i am sure that i am not the only one with the question, and good info is nice to have redundant.
I thought i recall reading you say go 3/4", but please confirm.
thanks
Josh
Yes you want 3/4 or more, closer to an inch. I and many others use the ride height as it is easier to check. We also know what our shock clearance is at that ride height. But whatever your reference point is, we are measuring the the distance Denny mentions above and that is the real number that matters.
Jim
East Street Auto Parts
Jim@Eaststreet.com
800 700 9080
#13
Posted 07-24-2011 09:39 PM
Josh
Yes you want 3/4 or more, closer to an inch. I and many others use the ride height as it is easier to check. We also know what our shock clearance is at that ride height. But whatever your reference point is, we are measuring the the distance Denny mentions above and that is the real number that matters.
Jim
+1 Agree with Denny and Jim. Pinch welds are not the same all the way around. No factory measurement spec for that area. I do know one spec miata racer who had his lazer leveled and cut at a frame alignment shop. I measured shock travel. I run the fat cats bump stop set up. I measured 3/4" of travel to the bump stop front and I like around 7/8" rear. I measured using a small tie wrap on the shock shaft.
1.) with you in car...
2.) bounce car to set ride height...
3.) roll back and forth to remove any suspension bushing binding...
4.) have skinny crew buy crawl under car (might be best up on setup stands or wood risers for the budget guy) and push tie wrap down to sit on top of shock body...
5.) slowly jack up one side of the car...
6.) measure distance between bottom of tie wrap to bottom of bump stop...
7.) repeat on other side...
8.) repeat, repeat, repeat until you get desired measurements.
9.) For last step, measure ride height somewhere else to be used as your future measuring point. I chose to measure from an inner mounting point since it is "less" likely to get bent than pinch welds. In the front, I use the flat cross member bar under the trans, the back big bolt. For the rear, I use the flat part of the inner frame bracing bar, under the front bolt. On my car, my front measuring point at 10.5 CM = about 3/4" of travel and the rear measuring point at 13.5 CM = about 7/8" of travel. I am finding that as I have become a more smooth driver, I have been able to start sneaking my ride heights lower and lower.
#14
Posted 07-25-2011 06:20 AM
Coat hanger gauge looks something like this: [_,------------------
See if you can mooch off of someone at track with scales. Start at 50% cross and wedge (most likely) or de-wedge depending on track. Accepted wisdom is < 0.5% wedge.
#15
Posted 08-01-2011 12:44 PM
You can also stager the front caster, if you like to play with your set up. I have done this for certain corners. more positive caster in the LF will make the car turn right better.
Frank
TnT Racing
SCCA Ohio Valley Region
#16
Posted 08-02-2011 07:36 PM
I have yet to cross weigh this car. I will soon though, before the Aug double. My latest question; how can you achieve a 50/50 cross weight with 200lb me in the left side while keeping a left/right ride height the same measurement?
#17
Posted 08-02-2011 08:44 PM
#18
Posted 08-03-2011 07:47 AM
Thanks guys! This is all great info!
I have yet to cross weigh this car. I will soon though, before the Aug double. My latest question; how can you achieve a 50/50 cross weight with 200lb me in the left side while keeping a left/right ride height the same measurement?
That is the $64,000 trick.
We setup a car last week. The driver spent countless hours trying to get it right. Before giving up. When we started, the car had 679 pounds of cross weight. YES< 600 POUNDS!!! It actually sat pretty level, the right side was a even but a little high. When we finished, the car had 1 pound of cross, sat level, and had 3* camber all around. Apparantly it worked, he won two races this weekend.
Dave
Dave Wheeler
Advanced Autosports, the nations most complete Spec Miata shop
Author, Spec Miata Constructors Guide, version 1 and 2.0
Building Championship winning cars since 1995
4 time Central Division Spec Miata Champion car builder 2012-2013-2014-2017
Back to Back June Sprints Spec Miata 1-2 finishes 2016 and 2017
5 time June Sprints winner in Mazda's
6 Time Northern Conference Champion Car Builder
2014 SCCA Majors National point Champion car builder
2014 SCCA Runoffs winner, T4 (Bender)
2014 Central Division Champion, ITS (Wheeler)
2013 Thunderhill 25 hour winning crew chief
2007 June Sprints winner, (GT1, Mohrhauser)
Over 200 race wins and counting.
www.advanced-autosports.com
dave@advanced-autosports.com
608-313-1230
#19
Posted 09-28-2011 09:14 AM
Couple of pics from Sunday Sep 24.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users