Jump to content

Photo

Test results from 1.6 header cleanup?

- - - - -

  • Please log in to reply
70 replies to this topic

#61
B(Kuch)Kucera45

B(Kuch)Kucera45

    Veteran Member

  • SMembers
  • PipPipPipPipPip
  • 568 posts
  • Location:Idependence
  • Region:NEOhio
  • Car Year:1991
  • Car Number:45
Just curious what a good TQ number is for a 1.6 ?
Kuch
Bona fide - A bonafide Spec Miata driver Instigator - Made a topic or post that inspired other

#62
Cnj

Cnj

    Member

  • Members
  • PipPipPip
  • 487 posts
  • Location:Dallas
  • Region:Sw
  • Car Year:1999
  • Car Number:32

Just curious what a good TQ number is for a 1.6 ?


97ft/lb. And be happy with it.

CNJ
  • Jim Drago and B(Kuch)Kucera45 like this
We have a Winnah! - Won their 1st race... Congratulations! Bona fide - A bonafide Spec Miata driver

#63
B(Kuch)Kucera45

B(Kuch)Kucera45

    Veteran Member

  • SMembers
  • PipPipPipPipPip
  • 568 posts
  • Location:Idependence
  • Region:NEOhio
  • Car Year:1991
  • Car Number:45

97ft/lb. And be happy with it.
CNJ

Haha

I'm looking for an actual pro motor 1.6 TQ numbers to compare with mine to see if I'm above ( :) ) or below the so call pro motor numbers before I head to the dyno with my new and improved manifold.
Kuch
Bona fide - A bonafide Spec Miata driver Instigator - Made a topic or post that inspired other

#64
Cnj

Cnj

    Member

  • Members
  • PipPipPip
  • 487 posts
  • Location:Dallas
  • Region:Sw
  • Car Year:1999
  • Car Number:32
Kuch,

I actually have no idea. Probably too much :)

Seriously though, Jim posted TQ values for all engines he sells just a few days ago. I'm too lazy to go find his post.

CNJ
We have a Winnah! - Won their 1st race... Congratulations! Bona fide - A bonafide Spec Miata driver

#65
Bench Racer

Bench Racer

    Different strokes for different folks : )

  • Members
  • PipPipPipPipPip
  • 5,508 posts
  • Location:Wauwatosa, WI
  • Region:Milwaukee
  • Car Year:1990
  • Car Number:14

Just curious what a good TQ number is for a 1.6 ?

If doing at BackStreet ask Saul and Rich. 


Broken record - You are starting to sound like a broken record. Donor - Made PayPal donation Bona fide - A bonafide Spec Miata driver

#66
Steve Scheifler

Steve Scheifler

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 2,816 posts

Hey Steve, so the shop (BSI Racing) did an initial dyno run with the car as was, then they cleaned up a manifold they had in shop, took the manifold off my car and cleaned it up and dyno'd both. The one on the car now posted the better result....with that being said, I don't know how the other cleaned up manifold performed.


OK. Not to be critical, nothing to be critical about, but so we have more information to include your experience can you tell me if he actually ran multiple runs first and tuned for a baseline? Was the drivetrain (trans and diff fluids) up to operating temps for each test, or were each of these quick single "cold" runs for comparison and not necessarily to compare with prior values? You mentioned similar results to Sean, on the same scale or just an improvement? Dyno charts?
Instigator - Made a topic or post that inspired other Broken record - You are starting to sound like a broken record.

#67
John Wilding

John Wilding

    Member

  • Members
  • PipPipPip
  • 80 posts
  • Location:United States
  • Region:CFR / Southeast
  • Car Year:1991
  • Car Number:126

OK. Not to be critical, nothing to be critical about, but so we have more information to include your experience can you tell me if he actually ran multiple runs first and tuned for a baseline? Was the drivetrain (trans and diff fluids) up to operating temps for each test, or were each of these quick single "cold" runs for comparison and not necessarily to compare with prior values? You mentioned similar results to Sean, on the same scale or just an improvement? Dyno charts?

 

Good morning Steve, I don't think the guys at BSI did that many runs or got that detailed - I specifically asked them to stay budget minded on the dyno time so the bill wouldn't be too crazy. I have the dyno chart from before the changes scanned into my computer, but the new dyno chart is in the trailer still, so I need to grab it over the next few days. 

 

When I get them both in the computer I'll post them for you all to see if you can extract any worthwhile information out of them. I'm still learning all this stuff, so I'm not worth any real feedback other than lap times and how the car felt throughout the sessions. 



#68
Jim Drago

Jim Drago

    East Street Racing / 2 Time National Champion

  • Administrators
  • 6,566 posts
  • Location:Memphis, Tn
  • Region:Mid South
  • Car Year:2005
  • Car Number:2
It is harder to test that type of change than most really believe it is..
better, worse or the same imo are almost meaningless unless you do dam near a full day of testing. small changes like diff, trans ,oil temps along with drum being warmed up are all potentially bigger changes than this modification. I have tested similar things and pulled what hair I have left out.. wasting a day and still not confident in my results. All these changes are within the margin of error of the dyno. So it can be a real task. IMO, the only true test of these type of changes is on an engine dyno with completely controlled conditions. We can get close,even give an educated opinion, but never a truly accurate one IMO.
  • dstevens, trimless, Sean - MiataCage and 3 others like this

East Street Auto Parts
Jim@Eaststreet.com
800 700 9080

NASA Champs Winner - NASA Champs Winner Hoosier Super Tour points Champion - Hoosier Super Tour points Champion ARRC Champion - Won the ARRC Race in a Spec Miata Series Champ - Won a points based series in a Spec Miata BFG Supertour Winner - Majors Winner - Circuit of the Americas Winner - We have a Winnah! - Won their 1st race... Congratulations! June Sprints winner  - June Sprints winner June Sprints winner  - June Sprints winner June Sprints winner  - June Sprints winner June Sprints winner  - June Sprints winner SCCA National Champion - Won SCCA Runoffs at Road America SCCA National Champion - Won SCCA Runoffs at Road America

#69
Tom Sager

Tom Sager

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 1,693 posts
  • Location:Chicago Suburbs
  • Region:Central
  • Car Year:1996
  • Car Number:94

Would it be fair to say for a 1.6 that the header grind will result in a 0 - 2.5 peak HP improvement, your results may vary?  


Donor - Made PayPal donation Bona fide - A bonafide Spec Miata driver We have a Winnah! - Won their 1st race... Congratulations! Make it Rain - Made Paypal donation of $100+

#70
Bruce Wilson

Bruce Wilson

    Gold Member

  • SMembers
  • PipPipPipPipPip
  • 663 posts
  • Region:Oregon
  • Car Year:1991
  • Car Number:68

Would it be fair to say for a 1.6 that the header grind will result in a 0 - 2.5 peak HP improvement, your results may vary?  

 

On an engine dyno

 

Could also potentially yield negative "measured" gains.  Knowing how to dyno and read results is one of those things everyone should learn.  There's lots to learn using the forums search tool (not directed at you, Tom).


I have an opinion so I must be right

Series Champ - Won a points based series in a Spec Miata Survivalist - Won 25 Hours at Thunderhill! We have a Winnah! - Won their 1st race... Congratulations! Bona fide - A bonafide Spec Miata driver

#71
Steve Scheifler

Steve Scheifler

    Veteran Member

  • Members
  • PipPipPipPipPip
  • 2,816 posts

It is harder to test that type of change than most really believe it is..
better, worse or the same imo are almost meaningless unless you do dam near a full day of testing. small changes like diff, trans ,oil temps along with drum being warmed up are all potentially bigger changes than this modification. I have tested similar things and pulled what hair I have left out.. wasting a day and still not confident in my results. All these changes are within the margin of error of the dyno. So it can be a real task. IMO, the only true test of these type of changes is on an engine dyno with completely controlled conditions. We can get close,even give an educated opinion, but never a truly accurate one IMO.


Agreed that it is more difficult than most believe, but not so much the rest depending on the chassis dyno and how it is used. Reliable and consistent results definitely require some experience, careful work and a lot more time than just strapping it down (or bolting it on) and doing a few pulls. And not all chassis dynos are created equal so your experience and mine are different. But it isn't by accident or chance that we can achieve the repeatability that we are seeing, and gains even half of what Sean listed would be clearly evident. So I come back to wondering why our particular engines are not responding to this modification. The most logical answer is that either our intake is limiting output so more exhaust flow makes little difference, or the exhaust is limited in other ways so removing the welds doesn't address the main restriction. I don't really buy either of those so I'm fishing for other explanations. I may try a straight pipe in place of the muffler just to see if that has any impact one way or the other. Perhaps I'll check with Sam Henry on his development of the SD system to see how it should respond.
Instigator - Made a topic or post that inspired other Broken record - You are starting to sound like a broken record.




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users