Body and Interior

Tunnel Notch Out Panel

We developed an insert that welds into the floor/tunnel area. This insert adds almost three inches of floor space to better mount your seat. Most seats in Miata's are mounted off center or crooked because of interference with the tunnel. Rather than beat the tunnel with a Big hammer, you call install this piece in about 30 minutes and have a nice crafts manlike job. This piece fits perfectly, it is even relieved in the front for the exhaust flange. It is a very easy install. You simply mark the floor/tunnel, then cut the floor out with a jigsaw or plasma cutter, lay this piece on top and weld or pop rivet in place. This piece lays over the factory seams and attaches at the seam of the floor from front to back and at the rear of the floor where the floor meets the rear trunk floor.

Front Lip (1999-2000)

Mazda Spec Miata OE-Style Front Lip (1999-2000)

Product from JAPAN made from high quality and flexible FRP. Gives a subtle but noticeable change to the look of the car by making it more aggressive. It will also make the car more stable at high speed.
Product Description

No cutting to the body needed
Flows really well with the lines of the car
Lightweight
Flexible
Only available for NB8C-1 Miata (1998-2000)

Universal Aluminum Seat Bracket

We all know how hard it is to mount a composite seat in a Miata. These brackets make it much easier. You have a 2 inch window of adjust-ability in each bracket. You can also mount a seat as low as touching the floor or as high as 4 inches off the floor and anywhere in between. Once you have your seat mounted and On the recline that you want, you can loosen the bolts and slide the seat anywhere, forward or back within that 2 in window without re drilling holes to fine tune your seat position. The brackets are also not offset. As you likely know, most of the time the bolts attaching the seat to the floor of Miata have to go under the seat, not toward the outside of the seat like in most cars with more room. With offset brackets, when you put the bolts under the seat, the offset portion designed to save you floor space actually uses up even more. So the 90 degree bend is the only way to go there.

These brackets will fit Side Mount Seats offered by: Momo, OMP, Cobra, Status, Racetech, Sparco, Recaro & most others. The brackets are made to bolt directly to sliders but have multiple slots for adjust-ability when direct mounting (eliminating sliders). The brackets are made from 3/16 inch thick Aluminum and weigh just under 3 lbs for the pair. Price listed is for a pair of brackets to mount one seat.

Floor drop panel

This is the best drop floor drop on the market. It comes with lap belt mounts and inner seat belt mount that is removed when you install a notch out panel (not pictured). Also notice the leading edge is on a 45 degree designed to glance off or over anything you may run over. Others on the market are 90 degrees and could rip the panel out or transfer all that energy right to your seat. This is not something to take lightly!! If you chose to put this modification in your car, research your decision and you will see why I believe ours is by far the best out there. They come preassembled with a detailed instructions.

interior mirror brackets

Most all of us have used mirrors that attach to the roll cage. Those mounts push the mirror too close to the driver. These staggered and adjustable brackets move the 14 in longacre mirror to the stock rear view mirror location. The brackets use two existing holes to locate themselves, no measuring or centering required. The brackets are staggered and adjustable to get the mirror in the desired position for every driver. Once installed and adjusted you will have no blind spots and be able to clearly see out the drivers and passengers windows as well as the back window. These brackets will make driving much easier than it was without them.

forward mount rear view mirror kit with longacre mirror

Most all of us have used mirrors that attach to the roll cage. Those mounts push the mirror too close to the driver. These staggered and adjustable brackets move the 14 in longacre mirror to the stock rear view mirror location. The brackets use two existing holes to locate themselves, no measuring or centering required. The brackets are staggered and adjustable to get the mirror in the desired position for every driver. Once installed and adjusted you will have no blind spots and be able to clearly see out the drivers and passengers windows as well as the back window. These brackets will make driving much easier than it was without them.

This option comes with longacre mirror

Aim display mounting brackets

We have AIM display mounting brackets. The brackets are specific to each display so please specify what display you have when paying.  The mounts will rivet or screw to the steering column covers and the display will be against the factory cluster and under the gauge hood.
Please specify what you need when ordering. If you don't see what you need, let us know, we will make it.

 

currently have display brackets for

MXS 1.2 MXL2 SOLO 2/SOLO 2 DL

VVT lip spoilers ( 2001-2005)

This is a prototype of the final product. Final product is in production now. They fit really well and look great. They made of fiberglass and are reinforced around the lower brake vent hole. The fog lite covers are no longer needed as the new air dam has the fog lite covers incorporated into the design. The introductory price is $400 delivered at either Homestead or Sebring races in January. The issue with these will be shipping. The shipping will be $125 plus as the part is over sized. So delivery is best when available.