Jump to content

Latest products

Shopping Cart

Your cart is empty right now


Add to cart

Universal Aluminum Seat Bracket

We all know how hard it is to mount a composite seat in a Miata. These brackets make it much easier. You have a 2 inch window of adjust-ability in each bracket. You can also mount a seat as low as touching the floor or as high as 4 inches off the floor and anywhere in between. Once you have your seat mounted and On the recline that you want, you can loosen the bolts and slide the seat anywhere, forward or back within that 2 in window without re drilling holes to fine tune your seat position. The brackets are also not offset. As you likely know, most of the time the bolts attaching the seat to the floor of Miata have to go under the seat, not toward the outside of the seat like in most cars with more room. With offset brackets, when you put the bolts under the seat, the offset portion designed to save you floor space actually uses up even more. So the 90 degree bend is the only way to go there.

These brackets will fit Side Mount Seats offered by: Momo, OMP, Cobra, Status, Racetech, Sparco, Recaro & most others. The brackets are made to bolt directly to sliders but have multiple slots for adjust-ability when direct mounting (eliminating sliders). The brackets are made from 3/16 inch thick Aluminum and weigh just under 3 lbs for the pair. Price listed is for a pair of brackets to mount one seat.


Add to cart

Front Lip (1999-2000)

Mazda Spec Miata OE-Style Front Lip (1999-2000)

Product from JAPAN made from high quality and flexible FRP. Gives a subtle but noticeable change to the look of the car by making it more aggressive. It will also make the car more stable at high speed.
Product Description

No cutting to the body needed
Flows really well with the lines of the car
Only available for NB8C-1 Miata (1998-2000)


Add to cart

Calibrated Air flow meters

These are calibrated 1.6 Air flow meters that, all have been precisely set with our bench testing procedures and then dynoed to insure accuracy. These are as good as you can get, the best for power through the curve.

We will refund the $50 core charge, once the cores are returned.


Add to cart

Hub seals 1990-2005

These seals are not available new or aftermarket anywhere. We have had them specially made for the SM hubs. We use these seals in all the hubs we build. The seals also provide far less drag than the factory seals. We only sell in pairs


Add to cart

East Street Racing Engines

If you want the best, that is what we have to offer.

East Street is currently offering engines before only available in our 35,000 plus cars. These engines are the best in the business. They win every weekend at every track in the country. They always make more HP than the competition. They powered our cars three National Championships and Sprints wins the five of the last six years running, along with multiple Runoffs poles, podiums and national wins. Your choices are simple, you can buy from us or follow those who already have.


Add to cart

Tunnel Notch Out Panel

We developed an insert that welds into the floor/tunnel area. This insert adds almost three inches of floor space to better mount your seat. Most seats in Miata's are mounted off center or crooked because of interference with the tunnel. Rather than beat the tunnel with a Big hammer, you call install this piece in about 30 minutes and have a nice crafts manlike job. This piece fits perfectly, it is even relieved in the front for the exhaust flange. It is a very easy install. You simply mark the floor/tunnel, then cut the floor out with a jigsaw or plasma cutter, lay this piece on top and weld or pop rivet in place. This piece lays over the factory seams and attaches at the seam of the floor from front to back and at the rear of the floor where the floor meets the rear trunk floor.


Add to cart

Ballast System Full Weight Plate (15 lbs)

The plate has four holes, with nuts welded on the back side. The weight plates(15 lbs, half plates are available 7.5 lbs) also have four holes in them, they lay flat on the base plate and attach with four 1/2 in grade 8 bolts. Weight plates can easily be changed in and out with little to no hassle.


Add to cart

Ballast System

After seeing many of the ways people install ballast in their cars, we decided there had to be a better way. What we decided to do is to secure the weight on the passengers side seat mounts. These mounts are designed to easily carry 200+ lbs securely. Our system comes with a steel base plate ( 19 lbs) that mounts securely to the four passenger seat mounting points. That plate has four holes, with nuts welded on the back side. The weight plates(15 lbs, half plates are available 7.5 lbs) also have four holes in them, they lay flat on the base plate and attach with four 1/2 in grade 8 bolts. Weight plates can easily be changed in and out with little to no hassle. With an impact you can change the plates in a matter of minutes. This is the best system out there, it is safe, secure, very easy to use and most of all looks professional, not a bunnch of bar bells or lead blocks.


Add to cart

East Street Racing Heads

This is an inexpensive way to get your car to top power

For Sale - East Street Racing Cylinder Heads
We are selling our racing heads to those who don't want to buy an entire engine or just want to replace a poorly performing or currently illegal cylinder head from one of our competitors. We build the heads to the letter of the rule and push each area to the edge of the spec,but never beyond. Our heads are simply the best that can be bought, period. Look at the results of our cars Sprints Qualifying four of the top 5 cars, Runoffs three of the top four cars had these heads, at the Runoffs Pole, Runoffs win, second and third along with Two NASA championships. We are simply making more power than anyone else!
$2000 exchange on 99 up
$1750 exchange on 90-97

$500 Core Charge

1990-2005 ready to install


Add to cart

Blue Printed Front Hubs

We have blueprinted front hubs available. These are the best rolling hubs out there bar none and the longest lasting. We start with new OEM castings as they are the ONLY ones that are heat treated all the way through the race and not just surface hardened. We completely go through these hubs, add new seals and install the highest quality steel ball bearings available ( standard bearings as not of the same grade and not as smooth and do not roll as free) . These hubs come with standard length studs. If you would like long studs, add $30 per hub. These hubs roll better than anything out there. This is what we use on all of our race cars that we build.
We are now offering a 6 month warranty on the hubs, races included.

$220 short studs
$250 long studs